- Magneteksan
- > Hand Magnets
- > Ø129×100 mm Quick Release Neodymium Hand Magnet for Insulation and Sheet Metal Cladding Work
Ø129×100 mm Quick Release Neodymium Hand Magnet for Insulation and Sheet Metal Cladding Work
Key Features
- Picks up sheet metal screws, rivets, binding wire and offcuts from the floor without bending down
- Ø129×100 mm stainless steel cylindrical body; the bottom face is the magnetic face
- Pull-release mechanism: pull the small handle on top and the collected parts drop off by themselves
- Wide rectangular carrying handle for comfortable one-hand use
- No power needed, permanent neodymium magnet system
The Ø129×100 mm quick release neodymium hand magnet was built to pick up small ferrous parts dropped on the floor during insulation and sheet metal cladding work. The bottom of the stainless steel cylindrical body is the magnetic face; when the magnet is brought close to the floor, screws, rivets, wire and sheet offcuts stick to it. The wide rectangular handle on top lets you carry the magnet with one hand. To empty it, pull up the small release handle on the lid; the magnet moves away from the bottom face and the parts drop into a box or bucket by themselves. There is no need to touch the parts by hand.
| Feature | Value |
|---|---|
| Product type | Quick release neodymium hand magnet |
| Model code | Ø129×100 mm Y82K5-CB |
| Body size | Ø129×100 mm |
| Magnet material | Neodymium (NdFeB) |
| Body material | Stainless steel |
| Magnetic face | Bottom of the body |
| Release | Pull-release handle |
| Carrying handle | Stainless steel rectangular handle |
| Maximum operating temperature | 80 °C |
| Power supply | None required (permanent magnet) |
| Application | Insulation job sites, sheet metal cladding and fabrication workshops |
Why Does Metal End Up on the Floor in Insulation Work?
In pipe, tank and duct insulation, rock wool or glass wool is usually covered with galvanised, aluminium or stainless steel sheet. While the sheet is cut, bent and screwed, sheet metal screws, rivets, binding wire and small sheet offcuts fall to the floor. They collect under scaffolding, between pipework and on the workshop floor.
Loose screws stick into shoe soles, puncture forklift and trolley tyres and increase the risk of slips and falls. A quick release hand magnet clears them quickly without bending down and picking them up one by one.
How to Use It
- Hold the magnet by the rectangular handle and move it over the floor with the bottom a few centimetres above the surface.
- Screws, rivets, wire and offcuts stick to the bottom of the body.
- Hold the magnet over a collection bucket or box.
- Pull up the small release handle on the lid; the parts drop into the bucket. Let go of the handle and carry on collecting.
At the end of a job, going over the spots where parts collect, such as under scaffolding, around the cutting area and along vehicle routes, clears the floor in a short time.
Where Is It Used?
- Industrial pipe, tank and duct insulation sites
- Sheet metal cladding cutting and bending workshops
- Roof and facade sheet metal installation areas
- Floor cleaning after piping and installation work
Limitations and Safety Notes
The magnet only attracts iron-based (ferromagnetic) parts; aluminium offcuts, aluminium rivets, copper and austenitic stainless steel parts are not held. The operating temperature must not exceed 80 °C. This is a strong magnet: keep it away from people with pacemakers or medical implants, magnetic cards and electronic devices, and keep your fingers clear when bringing it close to steel surfaces.
Other Models
Models in other sizes and handle lengths are listed on the hand magnets page. For reaching further without bending, see the Ø100×764 mm long-handled pull-release hand magnet. For custom sizes, please contact us.
Frequently Asked Questions
Does it pick up aluminium offcuts too?
No. Aluminium is not magnetic. The magnet picks up galvanised steel offcuts, steel sheet metal screws, steel rivets and binding wire.
How do I empty the collected parts?
Just pull up the small release handle on the lid. The magnet moves away from the bottom face and the parts drop off by themselves.
Can you make a different diameter or a long-handled version?
Yes. We make the body diameter, height and handle length to suit your application.




