- Magneteksan
- > Samarium Pot Magnets
- > Ø100×20 mm Samarium Pot Magnet with Handle for Heat Treatment Quench Tanks
Ø100×20 mm Samarium Pot Magnet with Handle for Heat Treatment Quench Tanks
Key Features
- Picks up washers, shims and small steel parts from the bottom of the quench tank without reaching into hot oil
- The Ø100×20 mm zinc plated steel body carries 7 samarium cobalt magnets on its front face
- Samarium magnets keep their strength at high temperatures far better than neodymium
- The long steel handle screws into the necked boss on the back of the body with an M10 thread
- No power needed, parts are removed by sliding them off the magnet face
The Ø100×20 mm samarium pot magnet with handle was built to pick up small steel parts that fall to the bottom of quench tanks on heat treatment lines. The front face of the zinc plated steel body holds 7 round samarium cobalt magnets, one in the centre and six evenly spaced around it. A long steel handle screws into the necked boss on the back of the body with an M10 thread, so the operator can reach the bottom of the tank without putting a hand in. The magnetic face is lowered towards the tank floor, washers, shims and similar parts stick to it, and the magnet is lifted out by the handle.
| Feature | Value |
|---|---|
| Product type | Samarium pot magnet with handle |
| Model code | Ø100×20 mm M10x20-B-7K-S5CCY |
| Body size | Ø100×20 mm |
| Magnet material | Samarium cobalt (SmCo) |
| Number of magnets | 7 round magnets (1 in the centre, 6 around it) |
| Magnet thickness | 5 mm |
| Body | Steel, zinc plated |
| Connection | Necked boss, M10 thread (20 mm) |
| Handle | Long steel handle |
| Power supply | None required (permanent magnet) |
| Application | Heat treatment quench tanks, retrieving parts from oil and liquid tanks |
Why Do Parts End Up in the Quench Tank?
In the automotive supply industry, small parts such as washers, shims, bushes and pins are dipped into an oil or water quench tank after leaving the hardening furnace. Parts that slip off a basket or conveyor, or pass through the gaps in a basket, collect at the bottom of the tank. They are lost production, and over time they pile up on the tank floor and affect circulation and cooling.
Reaching into hot oil by hand is dangerous, and draining the tank means hours of lost production. A pot magnet with a long handle lets you collect the parts from a safe distance while the tank is full and the line is running.
Why a Samarium Magnet?
Neodymium magnets lose pulling force quickly as temperature rises and are permanently weakened above a certain temperature. Samarium cobalt (SmCo) magnets keep their magnetic strength far better at high temperatures and also resist corrosion. That is why samarium is the choice for hot oil, hot water and areas around furnaces.
How to Use It
- Hold the magnet by the handle and lower it into the tank with the magnetic face pointing down.
- Move the face slowly across the tank floor; steel parts stick to the magnet.
- Lift the magnet out of the tank and let the oil drain off.
- Slide the parts off the magnet face towards the edge and into a container.
Sliding the parts across the face is much easier than pulling them straight off. You can collect parts at the end of each shift or whenever you notice them building up in the tank.
Limitations and Safety Notes
The magnet only attracts iron-based (ferromagnetic) parts; aluminium, brass, copper and austenitic stainless steel parts are not held. When working with hot oil, wear heat resistant gloves, safety glasses and suitable workwear, lower the magnet into the tank slowly and watch out for splashes. This is a strong magnet: keep it away from people with pacemakers or medical implants, magnetic cards and electronic devices, and keep your fingers clear when bringing it close to steel surfaces.
Other Models
Other diameters and connection types are listed on the samarium pot magnets page. For normal-temperature applications, see also neodymium pot magnets and hand magnets. For a handle length and magnet diameter to suit your tank depth, please contact us.
Frequently Asked Questions
Can you make the handle length to suit our tank?
Yes. We make the handle length to suit your tank depth, and the body diameter and number of magnets to suit the size of the parts you need to collect.
Does it also hold hardened (heat treated) steel parts?
Yes. Hardened carbon and alloy steel parts are magnetic and stick to the magnet.
How hot can the oil be?
Samarium magnets work at much higher temperatures than neodymium. Tell us the operating temperature of the oil or water in your tank and we will choose the right magnet grade together.




